 |
 |
 |
|
A Merit Series Power Conditioner is the perfect low-cost AC power
solution for any rack mount system. Install an M-8x2 in to the top slot
of your rack, and the eight switched outlets in the rear panel will
power up and protect all your equipment up to a 15-amp load. The M-8x2
is designed for applications where lights are not required.
 
Applications
Instrument Rigs
You've got a rack for your effects, preamps, tuner...You're going to
plug that into the wall? One big spike and your rig is up in smoke.
Furman's standard level surge/spike protection defends your gear from
the spikes and surges that are so common at gigs and practice spots.
With Furman's standard level RFI/EMI filtration, you'll get a quieter
tone without pops, crackles, and the local radio station coming out of
your amp.
Recording
Can't track down where that noise is coming from? Your mix sounding
flat? With Furman's standard level RFI/EMI filtration you'll lower the
noise floor caused by the dirty AC power coming into your console or
DAW. Furman's standard level surge and spike protection keeps your
sensitive digital equipment from acting funny or burning up due to
everyday spikes and surges. With a 15A capacity and nine total outlets,
it's enough to power your whole home studio.
DJ Equipment
Bars, clubs and other event venues have some of the worst power out
there - from air compressors turning on and off to light shows pulling
current loads up and down, the AC power can be a strain on the circuits
in your rig. Furman's standard level protection and filtration keeps the
bad stuff out.
Pro Audio
When you're out there gigging, you never know what kind of power
you're going to get. The wear and tear on mobile rigs eventually takes
it toll - that's why it's smart to plug into Furman's standard level
protection and RFI/EMI filtration. It keeps your equipment safe and
sounding clean. Whether you're setting up a show at the local club or
powering up the church band for their next service, make sure you give
them power they can trust. | Maximum Output Current: | 15 amps |
| Line Cord: | 6 ft., captive, 14 AWG, with 3-conductor Edison plug |
| Operating Voltage: | 120VAC 60Hz |
| Spike Protection Mode: | Line to neutral |
| Energy Dissipation: | 170 joules |
| Peak Impulse Current: | 12,000 amps |
| Maximum Continuous Opterating Voltage: | 130 VAC RMS |
| Let Through Voltage (@ 125 amps, 8/20uS waveform) | 400 volts |
| Noise Attenuation: | Transverse mode: Greater than 23dB, 200Khz to 10 Mhz |
| Dimensions: | 1.75” H x 19” W x 3.75” D |
| Weight: | 4.9 lbs. |
| Safety Agency Listing: | cTUVus |
| Warranty: | Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship. |
DATASHEET ( 0 bytes ) MANUAL ( 3 MB )
By Furman Sound:
What is the warranty coverage period on new Furman products?
Furman has Limited Warranty terms of one, three or five years (depending on the model). This warranty will cover
defects in materials or workmanship on registered units. Our warranty
covers parts and labor, with the term measured from the date of purchase
of the new unit by the original owner. The warranty is not
transferable.
How can I know if my unit is “in-warranty”?
SAVE YOUR SALES RECEIPT!
The receipt is your proof of purchase and confirms the product was
purchased at an authorized Furman dealer. It will need to be submitted
to Furman in order to process any warranty claims. Proof of purchase is
also required for any connected equipment warranty claim. No connected
equipment claim will be considered without a valid sales receipt.
|
|
|
 |
|
 |
|
